@Mert-Karabagli hi, please check the following page for the correct settings https://docs.iotcreators.com/docs/general-settings
Best posts made by Stefan de Lange
-
RE: Attaching Network-BC 95
-
RE: ThingsBoard via
Daarbij komt dat ik vind dat een dergelijke oplossing puur in de cloud moet kunnen worden gebouwd, zonder on-premise zaken. En dan dus ook nog in de gratis hoeken van de cloud.
Jammer. Een kastje of RPI in je meterkast is 100x leuker… (en gratis, behalve de HW dan). Draai er Node-RED op en al je problemen zijn opgelost.
-
RE: Collegial roaming?
@magnatron Is this for NB-IoT? As far as I know T-Mobile NB-IoT is not available on band 20 in NL.
@magnatron said in Collegial roaming?:
On band 8 auto-COPS works fine but on band 20 I have to set COPS to 1,2,“20404” before the CSQ goes below 99,99.
I don’t understand this part, the COPS command will force it to vodafone. What do you mean by CSQ goes below 99,99?
-
RE: ThingsBoard via
Hoi Sjimmie. Mooi dat je het werkend hebt gekregen.
{“latitude”: 52.136421, “longitude”: 5.262903}
Ik zou dit anders aanpakken. Aan de kant van NB-IoT wil je enkel kale bytes sturen, het sturen van JSON data creëert onnodig veel overhead.
Je zou het ook zo kunnen doen namelijk:
AT+CIPSEND=16
031B89E500504E37Is maar 8 bytes. In je python flask kun je dit vervolgens weer scheiden omdat je weet dat beide variabelen 4 bytes zijn:
latitude = 031B89E5
longitude = 00504E37Dan converteren naar decimale notatie en de komma weer terugplaatsen.
-
RE: Kan ik achterhalen welke SIM er in het modem zit?
@jeroend said in Kan ik achterhalen welke SIM er in het modem zit?:
@afzal_m Ik begrijp dat ooit de eerste 5 cijfers van de IMSI de operator code is, maar dat is niet meer zo. Enig idee hoe het kan?
Dit klopt nog steeds. Heb dit even uitgezocht voor de IMSI van mijn eigen T-Mobile NB-IoT simkaart:
901 40 XXXXXXXXX901 = International card
40 = Deutsche Telekom AG (aka T-Mobile) -
RE: MQTT Support
@aarttulp Hoi Aart. Ik ben wel benieuwd naar je usecase, wat zou je met MQTT wel kunnen wat je met HTTP nu niet kan? Je zou er ook nog aan kunnen denken om zelf een component te programmeren dat van MQTT -> HTTP vertaald en terug.
-
RE: Pincode simkaart starterspakket
@tvdl Probeer het nog een keer maar dan met PDP context:
(wacht bij iedere stap ff op OK of een bevestiging)
AT+CEREG=5 (netwerk info notifier) AT+CFUN=0 (radio uit) AT+CGDCONT=0,"IP","cdp.iot.t-mobile.nl" (set context) AT+CFUN=1 (radio aan) AT+COPS=1,2,"20416" (forceer registratie)
Check ook ff met:
AT+NCONFIG?
Of alle instellingen goed staan…
-
RE: Applicationserver koppelen aan iot portal(asp.net web api)
@tuyen-phan Hoi Tuyen.
Ik wil dat tmobile nu data verzend naar mijn server xx.xxx.xxx.xx/API/IoTTests/{data}. Maar ik Geloof dat alles momenteel wordt verzonden naar xx.xxx.xxx.xx/{data}. Hoe/waar kan ik die data vinden? Wat voor functie moet ik hiervoor schrijven?
Ik ben geen expert in programmeren en ik kan je dus niet helpen met de implementatie, maar ik zou het volgende doen:
- Geef in de API van T-Mobile het adres op waar jij wilt dat de data naar toe verstuurd wordt. Dit heb je al werkend gekregen, je hebt dus iets als https://<ip>/API/IoTtests opgegeven
- Je krijgt vervolgens op https://<ip>/API/IoTtests alle communicatie binnen van T-Mobile. Dit is in JSON- formaat, je krijgt dus een pakketje met daarin alle belangrijke info als IMEI nummer, netwerk tijd en natuurlijk de payload. De payload kan bijvoorbeeld sensor data zijn. Ik vermoed dat er wel een library functie is die iets doet als http.receivepacket() oid.
- Deze JSON moet je vervolgens uit elkaar plukken (ook wel parsen genoemd) om je payload te krijgen en die kun je dan opslaan…
-
RE: SerialSARAPassthrough MKRNB library - cannot see AT commands in serial monitor
@alessandro-mirabella Make sure you use the right COM port and the right GPIO for TX/RX. Also make sure you are actually sending something by testing with an FTDI adapter.
-
RE: Meer dan 120 berichten per dag
@peter-wit Kun je dan niet beter voor een andere technologie kiezen, zoals LTE-M of LTE CAT-0? Daar heb je over het algemeen een groter budget…
-
RE: Returning OK from endpoint
@sopwafel You could, but be aware of using PSM and expected latency. Your device might be sleeping again before it had the chance to receive a downlink message. I don’t know if it’s possible to use in combination with the T-Mobile CDP but you might want to take a look at LWM2M and CoAP. These protocols have acknowledgements build in.
-
RE: Arduino MKR NB1500: lukt niet om te verbinden.
@Crowdsourcer I think it’s not working because of old firmware. On a R410 with the most recent firmware I was able to send payload inline via AT+USOST=0,“172.27.131.100”,15683,11,“48656c6c6f20576f726c64” (also called ‘base syntax’). On a R410 with very old firmware (from 2018) that didn’t work so you have to use the ‘hex syntax’, which is sending the payload after sending the command.
I tried the following with the old firmware, that works:
[2020-04-27_12:06:54:125]AT+CFUN=0 [2020-04-27_12:06:54:860]OK [2020-04-27_12:06:57:092]AT+CGDCONT=1,"IP","cdp.iot.t-mobile.nl" [2020-04-27_12:06:57:111]OK [2020-04-27_12:06:58:556]AT+URAT=8 [2020-04-27_12:06:58:556]OK [2020-04-27_12:07:01:279]AT+CFUN=15 [2020-04-27_12:07:01:279]OK [2020-04-27_12:07:09:482]AT+CEREG=3 [2020-04-27_12:07:09:482]OK [2020-04-27_12:07:11:499]AT+CFUN=1 [2020-04-27_12:07:11:499]OK [2020-04-27_12:07:13:090]AT+COPS=1,2,"20416" [2020-04-27_12:07:13:098]OK [2020-04-27_12:07:20:349]AT+CGATT? [2020-04-27_12:07:20:349]+CGATT: 1 [2020-04-27_12:07:20:349]OK [2020-04-27_12:07:21:702]AT+CGPADDR [2020-04-27_12:07:21:702]+CGPADDR: 1,10.0.0.25 [2020-04-27_12:07:21:702]OK [2020-04-27_12:07:23:548]AT+USOCR=17,7000 [2020-04-27_12:07:23:559]+USOCR: 0 [2020-04-27_12:07:23:559]OK [2020-04-27_12:07:45:220]AT+USOST=0,"172.27.131.100",15683,11 [2020-04-27_12:07:45:220]@ <send hex data after @> [2020-04-27_12:07:45:220]48656c6c6f20576f726c64 [2020-04-27_12:07:49:524]+USOST: 0,11 [2020-04-27_12:07:49:524]OK
So you can use the hex syntax or upgrade your firmware and use the base syntax. It’s a good idea to upgrade your firmware anyway
-
RE: More messages than expected on application server.
@Martijn-Kooijman @Crowdsourcer According to datasheet SARA R4 will do 8uA in sleep mode.
-
RE: Quectel BC66, UDP, T-Mobile SIM in Germany: DNS parse failed
Hi, can you give us the full sequence of commands you use? That will help us find what is wrong.
-
RE: Quectel BC66, UDP, T-Mobile SIM in Germany: DNS parse failed
Hi, I am trying to reproduce this but my BC66 modem doesn’t even recognize the +QIOPEN command. So I am updating the FW first.
@Roalnd-Baldin said in Quectel BC66, UDP, T-Mobile SIM in Germany: DNS parse failed:
AT+QIOPEN=1,1,"UDP", "172.27.131.100",15683,1001,0,0 OK +QIOPEN: 1,565
I notice you have a whitespace between ‘,’ and “172.27.131.100”. I can’t verify but I know some modems don’t like this and will fail.
-
RE: When are we getting non-NeulMessenger CoAP?
@Sopwafel I agree, regular CoAP is awesome. The Neul Messenger protocol is only usable with a very limited number of modems
-
RE: QUECTEL BC95-B8 not connecting to Network
@jonasled You can enable more verbose error reporting with AT+CMEE=2. That will tell you what kind of error you have.
Quectel usually has their own version for every command so SARA N211 commands will not work.
What I can think of:
- Make sure you have the latest firmware
- Make sure the SIM works (try with a different module?)
- Make sure the antenna is properly connected
- Make sure you are in range of a network (scan with AT+COPS=?)
- Make sure you have a proper powersupply/cable (especially some USB supplies can be bad)
- Make sure you have the correct LTE bands enabled
- It should autoconnect to an available network but if it doesn’t you can force it with AT+COPS
-
RE: Downlink API dataformat
@Roalnd-Baldin 01AB uses twice the amount of data as hi if it’s received as ASCII
-
RE: RSSI and SNR in JSON response from API
@Uta You don’t need to derive it from the tower, the UE will measure those anyway (and I think it’s part of power control mechanisms). The tower also measures it’s own RSSI, not sure which one @MeneerJacco is referring to.
Anyway, it’s only a couple of bytes so doesn’t make a huge difference if it’s transmitted by the UE