using this connect command I just never get a connection
at.send(“AT+CGDCONT=1,“IP”,“cdp.iot.t-mobile.nl””) && at.recv(“OK”);
any ideas?
BC95-G
Revision:BC95GJBR01A01
+NCONFIG:AUTOCONNECT,TRUE
+NCONFIG:CR_0354_0338_SCRAMBLING,TRUE
+NCONFIG:CR_0859_SI_AVOID,TRUE
+NCONFIG:COMBINE_ATTACH,FALSE
+NCONFIG:CELL_RESELECTION,TRUE
+NCONFIG:ENABLE_BIP,FALSE
+NCONFIG:MULTITONE,TRUE
+NCONFIG:NAS_SIM_POWER_SAVING_ENABLE,TRUE
+NCONFIG:BARRING_RELEASE_DELAY,64
@afzal_m so - here is a more serious question :
In this case I have to register the IMEI in the portal using an API; the IMEI is the ID of the MODEM and not of the SIMCARD. I had assumed that we would manufacture boards in quantity and then then , just like a phone, whichever SIM card you put in would give the device its identity, its carrier, its commercial conditions. From what I see here the SIM card does not matter , it is the IMEI of the modem? Or am I getting this completely wrong?
Yup - worked
[rdResp]: +CPSMS: 1,“01000001”,“00000101”
[rdResp]: OK
[rdResp]: +NPING: “172.27.131.100”,253,654
[rdResp]: timed out
Initializing and connecting… SEND
Sending message through UDP
[rdResp]: 0
[rdResp]: OK
Created socket!
[rdResp]: 0,4
[rdResp]: OK
Length buffer vs sent:80
[rdResp]: OK
[rdResp]: OK
– should you send me new sim cards then for the starterspakket??
I have the new starters packket and a new SODAQ SARA board but using the example sketches (with a bit of extra debug from me) I can’t get past this error
I used the example UDP sketch
This with the up to date postman that I just installed
<html>
<head>
<title>JBWEB000065: HTTP Status 401 - </title>
<style>
<!--H1 {font-family:Tahoma,Arial,sans-serif;color:white;background-color:#525D76;font-size:22px;} H2 {font-family:Tahoma,Arial,sans-serif;color:white;background-color:#525D76;font-size:16px;} H3 {font-family:Tahoma,Arial,sans-serif;color:white;background-color:#525D76;font-size:14px;} BODY {font-family:Tahoma,Arial,sans-serif;color:black;background-color:white;} B {font-family:Tahoma,Arial,sans-serif;color:white;background-color:#525D76;} P {font-family:Tahoma,Arial,sans-serif;background:white;color:black;font-size:12px;}A {color : black;}A.name {color : black;}HR {color : #525D76;}-->
</style>
</head>
<body>
<h1>JBWEB000065: HTTP Status 401 - </h1>
<HR size="1" noshade="noshade">
<p>
<b>JBWEB000309: type</b> JBWEB000067: Status report
</p>
<p>
<b>JBWEB000068: message</b>
<u></u>
</p>
<p>
<b>JBWEB000069: description</b>
<u>JBWEB000121: This request requires HTTP authentication.</u>
</p>
<HR size="1" noshade="noshade">
</body>
</html>
@afzal_m here is another address to “delete” from the pre-registration of SODAQ
357518080040314
thanks
@jonathan-carter @afzal_m - can it be that I can’t get it regestered again on the net because this error 513 implies that the module is no longer registered ?
@jonathan-carter I looked up error 513 in the U-blox datasheets and it is :
513 Module not registered
@andre-rodenburg haha , yes I could do , but that makes the cost of the nbiot board pretty high 
@jonathan-carter I have a CSQ of
+CSQ: 20,99
and a STATS of :
>> AT+NUESTATS
"Signal power",-829[rdResp]: "Signal power",-829
"Total power",-720[rdResp]: "Total power",-720
"TX power",20[rdResp]: "TX power",20
"TX time",11725[rdResp]: "TX time",11725
"RX time",311912[rdResp]: "RX time",311912
"Cell ID",2362982[rdResp]: "Cell ID",2362982
"ECL",1[rdResp]: "ECL",1
"SNR",19[rdResp]: "SNR",19
"EARFCN",3747[rdResp]: "EARFCN",3747
"PCI",352[rdResp]: "PCI",352
"RSRQ",-131[rdResp]: "RSRQ",-131
OK[rdResp]: OK
@jonathan-carter still the same
I also get no success or failure from the module either
PENDING=0,SENT=0,ERROR=0[rdResp]: PENDING=0,SENT=0,ERROR=0
@afzal_m I am doing a project for Adriaan van Eck, so I amusing his portal on
plafundum2@yahoo.com
@afzal_m thanks
I tried it and I get this error on sending >
+CME ERROR: 513[rdResp]: +CME ERROR: 51
is this because I have to no re-register it?